14-Jan-2019Loveland, CO+12 milesAuto Parts for Sale
A very nice set of early brass lights for various early autos Very nice, driver quality lights Reflector liner in the tail light has been resilvered Liners in the sidelights are original Good fonts with burners Priced reasonable at $1,750. for the set
Pickup topper cls. I have two sets of four. They are faster and easier than bolting your topper down and dont require drilling. Asking $25 per set of four.No spam please.
One set of nerf bars for standard cab pkup. Never have been mounted, I dont have any of the mounting hardware. There isnt much needed for mounting. Asking $50No spam please.
JR West Coast Truck Mirror will fit either side left or right. Clearing out garage. Still in box never been mounted, may trade.
This hood is a factory GM part direct Fromm Detroit. Fits all GM trucks, K Blazers, and Suburban as well as GMC from 1981 to 1991. No rust, clean as new. $175.00 for a real hood or buy the flimsy import parts.
Here is a rust free Suburban shell. This body is pretty much the same from 1973 to 1992, with small variations. If your done chasing rust then this body is for you.What you get Body only with quarter glass, interior trim and whats left of interior panels.No door, fenders, hood, tailgate
We have a stock jeep Dana transmission transfer case skid plate that fits all the Dana 300 tc series jeeps from 1980 to 1986. I will also work on earlier CJ-series jeeps from 1976 to 1979 if using the Dana 300 transfer case. Skid plate is in great shape, no rust. Key Words Jeep, AMC, CJ, CJ5, CJ-5, CJ7, CJ-7, CJ8, CJ-8, Scrambler, Dana, 4x4
I have a really heavy duty old snow plow that is set up for power angle. This a a bare plow, no hydraulic rams, no sub frame vehicle side. The plow is 90 wide and can pivot for angles. I do find a single valve pump you can have. ThanksRay
I have a realy nice Konig PTO winch. This is mounted on the front of a CJ5 Jeep, It can mount on the rear of the jeep if brackets are made to hold the winch. I also have rear working PTO units that attach to the rear of the Model 18 transfer cases to use for rear implements. Willys, CJ. CJ2A, CJ3A, CJ5, CJ6, GPW, MB, M38, M38A1, M606, M170,
Here is a set of front and rear BDS 2.5 lift springs that fit all CJ5, CJ6, M38A1 and the M170 jeeps from 1952 to 1975. The springs are in great shape, light use, Comes with new front and rear new spring bushings uninstalled. Also have lots of Willys and CJ parts.Willys, CJ, CJ5, CJ6, M38A1, M170, Kaiser, AMC
This is a widetrack AMC 20 rear axle, it is complete hub to hub. Measures 56 from wheel mounting surface to wheel mounting surface. 354 gear ratio, none posi. Was in working order when pulled from service.82-86 CJ7 CJ8 as a replacement. Very nice up grade to any CJ series jeep or Willys
This is a factory tan padded dash that AMC used with the Levi packages and other models. The dash is in super shape for the age. Fit jeeps from 76-86.
I have a few parts that need to find a home. Please view each picture closely, There are lots of stuff per photo. If there is some thing of interest feel free to see if its still available. All parts are very usable and have life left in them. NOTE LOW BACK BUCKET SEATS SOLDWilly, Willys, Willies, willis, CJ, cj5, cj7, scrambler, Jeep, 4x4, kaiser, AMC
We have a lot of little parts stuff for CJ series jeeps and Willys jeeps. Look at the pictures and keep in mind that your seeing just a taste of you is collected over the years. This all stock OE jeep parts folks, not the after market stuff that works some times. Hit me up with your list and Ill see what I have. I will need a few days to get back with you since I need to dig around the barns.Wi...
This 1984 engine is a AMC 4.2 liter 258. Welcome stroker builders, this it the crank shaft you need to stroke your 4.0 engine to a 4.7. The price is for the long block so no intake, carb, or accessories. This engine is being sold as a builder, not a running engine.Block number 402C10JEEP AMC WRANGLER WILLYS CJ5 CJ7